Replies created

 

Viewing 7 replies - 1 through 7 (of 7 total)
  • wrenchmaster
    Participant

    Josh,

    I have that problem too.

    Roland TD-25 trigger , Roland UM-One MK2, Personas Studio 2/6, EZDrummer2 and a Simmons DA200

    wrenchmaster
    Participant

    I don’t have any of the MIDI mac interface with the triangles set up. I was told by Sweetwater that I didn’t need to use this.
    I used it when I wasn’t using EZDrummer. Should I still be using it?

    Roland TD-25 trigger , Roland UM-One MK2, Personas Studio 2/6, EZDrummer2 and a Simmons DA200

    wrenchmaster
    Participant

    @Brad said:
    Do you have your TD3 connected to your host (PC/Mac, whatever) and have you used it in Studio One? Trying to figure out where to start. Essentially sounds is produced by triggering EZDrummer 2 with you TD3. So once you have your TD3 connected to your host installed any drivers that are required and configured it, start EZDrummer 2 up going into settings > audio/MIDI setup and select MIDI Device, your TD3 should show up in the list and select and apply.

    That should allow you to trigger EZD2 directly from your TD3. Hope this helps.  

    Yes, I have a UM-One midi cable connecting the TD-3 and the Mac Mini.

    Roland TD-25 trigger , Roland UM-One MK2, Personas Studio 2/6, EZDrummer2 and a Simmons DA200

    wrenchmaster
    Participant

    Can anyone explain..

    Can someone explain how the sound is produced and transferred so I can understand what the technical
    functions behind the scenes are and what different software and hardware is used and for in the process?

    Roland TD-25 trigger , Roland UM-One MK2, Personas Studio 2/6, EZDrummer2 and a Simmons DA200

    wrenchmaster
    Participant

    I’ve updated my signature with my equipment

    Roland TD-25 trigger , Roland UM-One MK2, Personas Studio 2/6, EZDrummer2 and a Simmons DA200

    wrenchmaster
    Participant

    Just reporting back that I got the kit working, THANKS!!!!

    I’m now trying to figure out how best to control music input output volumes vs the drum sample volumes.

    Roland TD-25 trigger , Roland UM-One MK2, Personas Studio 2/6, EZDrummer2 and a Simmons DA200

    wrenchmaster
    Participant

    Right now, I have the EZDrummer sounds out my Simmons if I click the Mac screen preview of the instruments, but get the Roland TD-3 sounds out the headphones and Simmons , when I hit the actual Roland toms.

    wOK, let me describe my hardware….

    I have a TD-3, Roland UM-ONE mk2, MacMINI, and Simmons Amp
    1) hook up your TD-3 module’s MIDI Out with your computer’s MIDI interface IN

    Are referencing to UM-ONE? And where should it be connected, (both ends)?
    2) launch EZdrummer 2 and go into the ‘Audio/MIDI Setup…’ and make sure there is a check mark in your MIDI Device’s check box, hit OK

    You mean the the UM-ONE?
    3) make sure you have sound when you click the drums in the EZdrummer 2 interface

    4) go to the Ezdrummer 2 Menu (in the upper right corner of the interface) and click ‘Settings > E-drums…’. Then select the Roland Mapping.
    I know where this is..

    BR,
    John

    Roland TD-25 trigger , Roland UM-One MK2, Personas Studio 2/6, EZDrummer2 and a Simmons DA200

Viewing 7 replies - 1 through 7 (of 7 total)

No products in the cart.

×